Semi-auto One Blowers One Heater Plastic Bottle Blow Molding Machine
Product Description
Products Description
Semi-auto One Blowers One Heater Plastic Bottle Blow Molding Machine is suitable for producing PET plastic containers and bottles. It is widely used to produce the carbonated bottle, mineral water, carbonated drink bottle, pesticide bottle oil bottle cosmetics, wide-mouth bottle etc.
•Adopting double crank to adjust mold, heavy locking mold, stable and fast,. Adopt infrared oven to heat the perform, the perform rotated and heated equally.
•The air system has been divided into two parts: pneumatic action part and bottle blow part to meet the different requirements for the action and blow. It can provide sufficient and steady high pressure for blowing large irregular shaped bottles.
•The machine is also equipped with muffler and oiling system to lubricate the mechanical part of the machine.
•Adopting double crank to adjust mold, heavy locking mold, stable and fast,. Adopt infrared oven to heat the perform, the perform rotated and heated equally.
•The air system has been divided into two parts: pneumatic action part and bottle blow part to meet the different requirements for the action and blow. It can provide sufficient and steady high pressure for blowing large irregular shaped bottles.
•The machine is also equipped with muffler and oiling system to lubricate the mechanical part of the machine.
| Main Technical Date | |||||
| Model | SKY-12 | SKY-8Y | SKY-SA4 | SKY-5L | SKY-10L |
| Bottle Volume | 10L-25L | 0.01L-2L | 0.01L-2.5L | 0.01L-5L | 5L-10L |
| Theoretical Output | 90-180pcs/h | 1200-1600pcs/h | 2000pcs/h | 300-800pcs/h | 300-500pcs/h |
| Blower(L*W*H) | 218*77*196cm | 160*60*161cm | 190*88*180cm | 175*67*186cm | 193*72*183cm |
| Blower/Weight | 1000kg | 500kg | 1000kg | 600kg | 800kg |
| Heater(L*W*H) | 237*68*135cm | 187*63*145cm | 190*66*160cm | 187*63*145cm | 187*63*145cm |
| Heater/Weight | 380kg | 250kg | 380kg | 250kg | 250kg |
| Power | 40kw | 17.5kw | 18kw | 17.5kw | 17.5kw |
Main Features
A. Stable performance with advanced PLC.
B. Conveying preforms automatically with conveyor.
C. Strong penetrability and good and swift distribution of the heat by letting the bottles rotate by itself and revolute in the
rails simultaneously in the infrared preheater.
D. High adjustVability to enable the pre-heater to preheat preforms in shapes by adjusting the light tube and the length of the reflecting board in the preheating area, and eternal temperature in the preheater with an automatic thermostatic apparatus.
E. High safeties with security automatic-locking apparatus in each mechanical action, which will make the procedures turn into a state of safety in case of a breakdown in certain procedure.
F.No contamination and low noise with the air cylinder to drive the action instead of the oil pump.
G. Satisfaction with different atmospheric pressure for blowing and mechanical action by dividing the blowing and action into three parts in the air pressure diagram of the machine.
H. Strong clamping force with high pressure and double crank links to lock the mold.
I. Two ways of operating: automatic and manual.
J. Safe, reliable, and unique design of the position of valve to make the air pressure diagram of the machine easier to
understand.
K. Low cost, high efficiency, easy operation, easy maintenance, etc, with automatic technological process.
L. Contamination is avoided for the bottle body.
M. Ideal effect of the chilling with the chilling system.
N. Easy installation and starting
O. Low rejection rate: less than 0.3percent.
B. Conveying preforms automatically with conveyor.
C. Strong penetrability and good and swift distribution of the heat by letting the bottles rotate by itself and revolute in the
rails simultaneously in the infrared preheater.
D. High adjustVability to enable the pre-heater to preheat preforms in shapes by adjusting the light tube and the length of the reflecting board in the preheating area, and eternal temperature in the preheater with an automatic thermostatic apparatus.
E. High safeties with security automatic-locking apparatus in each mechanical action, which will make the procedures turn into a state of safety in case of a breakdown in certain procedure.
F.No contamination and low noise with the air cylinder to drive the action instead of the oil pump.
G. Satisfaction with different atmospheric pressure for blowing and mechanical action by dividing the blowing and action into three parts in the air pressure diagram of the machine.
H. Strong clamping force with high pressure and double crank links to lock the mold.
I. Two ways of operating: automatic and manual.
J. Safe, reliable, and unique design of the position of valve to make the air pressure diagram of the machine easier to
understand.
K. Low cost, high efficiency, easy operation, easy maintenance, etc, with automatic technological process.
L. Contamination is avoided for the bottle body.
M. Ideal effect of the chilling with the chilling system.
N. Easy installation and starting
O. Low rejection rate: less than 0.3percent.
Details Images
| Configuration list | |
| PLC controller PLC | MITSUBISHI |
| Touch screen | MITSUBISHI |
| Cylinder | SMC, Japan SMC |
| Filter | TPC, Korea TPC |
| Magnet valve | TPC, Korea TPC |
| Photoelectric switch | OMRON,Japan |
| Contactor | Schneider,France |
| Proximity switch | SICK ,German |
| Sensor | OMRON,Japan |
| Switch power | MEANWELL,Taiwan |
| Frequency converter | Mitsubishi,Japan |
| Main Servo motor | XINJIE CHINA |
| Feeding Servo Motor | XINJIE CHINA |
FAQ
1. A: Are you factory?How many workers do you have?
B: Yes,we are factory. our factory is located in zhangjiagang near from shanghai. We have about 50 workers in our factory.
2. A: What about after sale service?
B: 12months of electrical part and 18months of mechanical part after machine installed and running normally.
3. A: What about installation?
B: Our engineer can be sent to your country. but customer should pay the air tickets and 100usd as salary per person per day. besides, customer should arrange the accommodation for them during the trip.
4. A: What do we do if we encounter problem about the machine ?
B: Show us the picture or video of the problem. If the problem is from small machine, we will send you solution by video. If the problem is from large machine, our engineer will go to your factory (customer will pay the fee during the trip).
5. A: How can you control the quality and delivery?
B: All our machines will be tested before packaging. wooden packaing is strong and safety for long delivery.